Difference Between HD-CVI, AHD, HD-SDI and HD-TVI

TDK 2 SIM GSM Land Phone

FEATURES

• Support GSM900/1800Mhz; GSM850/900/1800/1900Mhz optional
• Caller ID
• Dot-matrixed display with Spanish,English, Chinese, optional
• SMS function
• IP No. Setting
• Software upgrade jack
• Data service, Support CSD and GPRS class 10/8. Connect PC by USB port
• Call in / Call out /Call divert/ Call waiting limitation function
• Lock up function: SIM card, network, cell and operated company
• Local No. / direct No. / limited No. Setting
• Speed dial function
• Redial function
• Support three-way conference call
• Save more than 100 SMS on the phone
• 7-level headphone volume and silence adjustable
• Speaker Phone
• Low-power indicator
• Storage 20 missed call or received calls and the last ten dialed number
• Voice mail function
• Packing Size (mm): 220*160*53
• Emergency call: At off-hook or hand-free state, can calling emergency number without
• Operating Freq.: GSM900-1800Mhz/850-1900Mhz automatically switch
• Normal operation temperature: -30 ---70
• Restricted operation temperature: -30 ---80
• Storage temperature: -40 ---85
• Environment noise: Below 60dB(A)
• Support SIMCard 1.8V/ 3V
• Channel interval: 200KHz
• Receive sensitivity
  

XDEN Turbo HD DVR CCTV - XD-B204C-X1, XD-B208C-X1 and B216-X1

XDEN Turbo HD DVR  CCTV - XD-B204C-X1, XD-B208C-X1 and B216-X1

Compact High Efficiency Turbo HD DVR for HD CCTV Security System in Pakistan

> H.264 / H.264+ and Dual-stream video compression
> Support both HD-TVI / Analog and AHD cameras with adaptive access
> Full channel recording at up to 720p & 1080P resolution
> HDMI and VGA output at up to 1920×1080P resolution
> Long transmission distance over coax cable
> Support 4 / 8 / 16-CH synchronous playback at 720P, 1080P resolution

Product Details:

4-CH DVR Model No. XD-B204C-X1, XD-B204D-X1-N
8-CH DVR Model No. XD-B208C-X1, XD-B208D-X1-N
16-CH DVR Model No. XD-B216C-X1, XD-B216D-X1-N

XDEN Turbo HD DVR Specifications:

Video/Audio Input
Audio Input:	|	1-ch
Video Compression:	|	H.264, H.264+
Analog and HD-TVI video input:	|	4-CH (XD-B104C-X1) and 8-CH (XD-B108C-X1) BNC Interface (1.0Vp-p, 75 Ω)
Supported camera types:	|	Support HDTVI input: 720P/25Hz, 720P/30Hz, 1080P/25Hz,30Hz Support AHD input: 720P/25Hz, 720P/30Hz, 1080P/25Hz,30Hz support CVBS input
Audio Compression:	|	G.711u
Audio Input Interface:	|	RCA (2.0 Vp-p, 1 kΩ)
Two-way Audio:	|	1-ch, RCA (2.0 Vp-p, 1 KΩ) (using audio input)
Video/Audio Output
HDMI/VGA Output:	|	1920 × 1080 / 60 Hz, 1280 × 1024 / 60 Hz, 1280 × 720 / 60, 1024 × 768 / 60 Hz
Recording resolution:	|	Main stream: 720P / WD1 / 4CIF / VGA / CIF Sub-stream: CIF  / QVGA / QCIF (real-time)
Frame Rate:	|	Main stream: 720p / WD1 / 4CIF / VGA / CIF@25fps (PAL) / 30fps (NTSC) Sub-stream: CIF / QVGA / QCIF@25fps(PAL) / 30fps (NTSC); 4CIF/2CIF@6fps
Video Bit Rate:	|	32 Kbps ~ 4 Mbps
Stream Type:	|	Video / Video&Audio
Audio Output:	|	1-ch RCA(Linear, 1kΩ)
Audio Bit Rate:	|	64kbps
Dual Stream:	|	Support
Playback Resolution:	|	720P / VGA / WD1 / 4CIF / CIF / QVGA / QCIF, 1080P
Synchronous Playback:	|	4-Ch for (XD-B204C-X1), 8-CH for (XD-B204C-X1) & 16CH For (XD-216C-X1)
Network management
Remote connections:	|	128
Network protocols:	|	TCP/IP, PPPoE, DHCP, Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, iSCSI, UPnP™, HTTPS
Hard Disk Driver
Interface Type:	|	1 SATA Interface for 4&8 and 2 SATA for 16 CH
Capacity:	|	Up to 6 TB capacity for each disk
External Interface
Network Interface:	|	1 10M / 100M self-adaptive Ethernet interface
USB Interface:	|	2 USB 2.0 Interfaces
General
Power Supply:	|	12V DC
Consumption:	|	≤20W(without hard disks)
Working Temperature:	|	-10 ºC ~ +55 ºC (14 ºF ~ 131 ºF)
Working Humidity:	|	10% ~ 90%
Dimensions:	|	285 × 210 × 45 mm (11.2 × 8.3 × 1.8 inch)
Weight:	|	≤ 1.2 kg / 2.6 lb (without hard disks)

How to set up DVR to watch CCTV security cameras over Internet

Watch CCTV security cameras over Internet (Tutorial)

How to set up a DVR to watch CCTV security cameras over Internet from a remote place, if you have an Internet connection with a static IP address

1. Connect your DVR to your router
2. Use menu on your DVR to assign internal IP, gateway and port number.
   
   This Local IP must be in the same Gateway range as your Router. If you are unsure, check the Router and locate the Status section.
   
   Alternatively use the the Command prompt of Windows 8/7/Vista/XP/2000 and type in ipconfig.
   Look for Gateway. If the Gateway is 192.168.1.1, then you can make the DVR's IP anything from 192.168.1.2 to 192.168.1.255.
   
   Also you will need to use the same SubNet Mask, which is typically 255.255.255.0, and the same gateway.
3. Next find out what port your DVR uses. The easiest way to do it is by reading the manual of your DVR. See the network section of the manual.
   
   If your DVR comes with network software, it may show the port number in the connection area.
   
   Check the Server software/Programming (Network section of it) to see if the port is listed there.
   
   In many cases the port number will be 80, which is an HTTP port.
4. Set your router to forward the chosen port to the internal IP address of DVR.
   
   To access the Router itself, use the Gateway you just located. If the gateway is 192.168.1.1, then enter that into the location edit box of your browser and then click the Enter button. A username and a password are typically required, but it depends on a router. For Linksys use "admin", "admin". By default DLink doesn't require any username or password (Please note that it is highly recommended to change the default password).
   
   
   Once you're logged into the Router, go to the Applications & Gaming Section / Servers of the Router and add a Server/Application. Enter the port number and select TCP only. Where it says Port 0 to 0 enter the same port number twice. Or if your DVR uses, for example, ports 3550, 4550, 5550, 6550, and there is nothing else utilizing these ports in between, then you can actually just enter one line, 3550 - 6550.
   
   Enter the DVR/Cameras internal IP.
   
   Enable it.
   
   
   
   Example:

   If the port was 1025, and the Local IP is 192.168.1.201, then the corresponding settings will be the following:
   
   NAME = Anything you want
   Port = 1025 TO 1025
   TCP/UDP = TCP
   LOCAL IP = 192.168.1.201
   ENABLED = CHECKED
   
   or
   
   NAME = Anything you want
   Port = 3550 TO 6550
   TCP/UDP = TCP
   LOCAL IP = 192.168.1.201
   ENABLED = CHECKED

5. Set up additional entries for as many ports as your DVR uses, but use the same local IP address. Check your DVR manual and it's networking section for all additional ports required. Also check the DVR software itself.
   
   If your router has enough free entries, you can separate them. Use it like DVR_HTTP for the browser port, DVR_AUDIO for the audio port, DVR_VIDEO for the video port, etc.
   
   If you are going to use Virtual Network Computing (VNC) to a PC DVR, then you will need to set up port 5900, and perhaps call it VNC_DVR, for example.
6. If you have a static IP address, then you should be able to enjoy viewing your CCTV cameras from a remote place by now. Just enter your static IP address in a browser in a remote location, and your router should forward packets to your DVR.s
   
   If you have a dynamic IP address, then you will need to set use a Dynamic DNS service, so that you can access your DVR by a memorable address.

---

One of the biggest challenges setting up a DVR to watch CCTV security cameras over Internet from a remote place is that all routers are different, so there are no general instructions on how to set them up. You need to refer to the router manual provided by the manufacturer of your router.

Another problem is that some Internet providers do not provide static IP addresses using dynamic IP addresses instead.

How to set up a Dynamic DNS (DDNS) service and DVR to view CCTV cameras over Internet from a remote place, if you have a dynamic IP address

First, you need to find a Dynamic DNS (DDNS) service. Free services usually don't last too long or have their limitations. Paid Dynamic DNS services cost about USD $20-$25 per year. If you have your own server with BIND, you may set up your own Dynamic DNS service. Let's assume you will use a 3rd party dynamic DNS service (DDNS) for your DVR.

• Create an account with a username and password at a Dynamic DNS service (free or paid).
• Login to your account
• Go to "Account" -> "My Service" -> "Add Host Services" -> "Add Dynamic DNS Host"
• Enter and select hostname
• Enter the IP address of your computer
• Click "Add host"
  In your DVR software:
  • Find DDNS network settings
  • Enable DDNS
  • Enter username, password and hostname from your Dynamic DNS account
  • Apply the settings

Now if your IP address changes, your DVR software will send the data to Dynamic DNS (DDNS) service, so the data there will be updated. This allows to access your computer from a remote location by using a memorable name (user-friendly hostname) instead of a weird IP address.

p.s. Please note that some routers can also be configured to work with DDNS, so instead of configuring your DVR software, you may configure your router.

---

Problems setting up a remote DVR viewing when your ISP uses network address translator (NAT) or proxy server

When you check the IP address of your computer, please make sure it is not in the following ranges:

10.0.0.0 - 10.255.255.255
172.16.0.0 - 172.31.255.255
192.168.0.0 - 192.168.255.255

The IP addresses from these ranges are common in home and office local area networks (LANs), as globally routable addresses are scarce, expensive to obtain, or their use is not necessary. These addresses are private because they are not globally delegated, meaning they aren't allocated to a specific organization. If such a private network needs to connect to the Internet, it must use either a network address translator (NAT) gateway, or a proxy server. If you have such an IP address, then I can't help you to set up remote DVR viewing. You need to ask your ISP whether you can get a real IP address or port forwarding.

X-Den Wifi Camera W15

 

  

 

 

 

How to Configure YooSee Wireless IP Camera

 

YooSee Wifi Cameras Configuration Click Here to View Pdf 

How-to Connect a Security Camera DVR to a Wireless Router

Sometimes customers install CCTV DVRs in locations that do not have a hard wired Network connection. For example, maybe you ran all of your RG59 or CAT5 cable for your security cameras back to a closet where your DVR will be located, but you had no way to run a network cable from your wireless router to that location. Most CCTV DVRs and network recorders for IP cameras only have a wired Ethernet port (no built-in WIFI).
Now, you want to view your security cameras remotely over the Internet and in order to do this, you need to connect your DVR to your router.

What can you do?

 
Click Here for Video

Wireless Network Diagram to Connect DVR to WIFI Router

This is how it works using the above example installation.

1. There are two X-Den security cameras hard wired to an DVR surveillance DVR. using RG59 coax cable. However, this solution works the same if you are using IP cameras with a network video recorder.
2. The DVR only has Ethernet port for network connectivity (no built-in WIFI).
3. The Ethernet port of the DVR is hard wired to the wireless bridge using CAT-5e cable. I am using a WIFI-AP3500 for the wireless bridge. The WIFI-AP3500 is actually a multi-purpose wireless device. It can be configured as a router, access point, or bridge. This one is configured in bridge mode which enables it to connect to our router.
4. The WIFI-AP3500 is configured to connect to the Linksys / Cisco wireless router using the WIFI.
5. The Linksys router is connected to the Internet. This can be using a DSL, cable, dedicated fiber, or any other type of modem / Internet connection.